Motion Control Couplings

Lovejoy ES Series single beam set screw style couplings protects the shaft support bearings from damaging thrust and radial load due to misalignment and axial motion. These motion control couplings have a zero-backlash design to correct angular misalignments up to 7 degrees and are coated with anodized aluminium finish ensuring heat resistance and chemical stability. They facilitate easy one-piece installation while delivering nominal torque up to 17 in-lbs. Choose from a wide range of these single beam clamp style couplings available in outside diameters of 19, 23, 32 and 38 inches on Raptor Supplies.

Ruland Manufacturing coupling hubs are designed for connecting shafts for torque transmission applications. These are one of the components for the three-piece design comprising 2, anodised aluminium hubs & a centre disk. These couplings can accommodate high parallel misalignments and operate with low bearing loads, thereby protecting sensitive system components. They have lightweight aluminium construction and black oxide finish for preventing abrasive fluids & particles from damaging the coupling hubs. Choose from a wide range of these coupling hubs, available in 7/8, 3/4, 5/8, 1/2 & 1 inch bore diameters.

Ruland Manufacturing coupling hubs are designed for connecting shafts for rotary torque transmission applications. These are one of the components for the three-piece design comprising 2, anodised aluminium hubs & a centre disk. These couplings operate with low bearing loads, thereby protecting sensitive system components like bearings and can accommodate high parallel misalignments. They have lightweight, 2024-T351 aluminium construction and black oxide finish for preventing abrasive fluids & particles from damaging the coupling hubs. Choose from a broad range of these coupling hubs, available in 5/16, 3/8, 5/8, 3/4 & 1/2 inch bore diameters.

Ruland Manufacturing MOCT Series coupling oldham clamps are ideal for connecting shafts with misalignment while transmitting torque. They maintain precise alignment between two shafts while allowing axial movement to prevent angular, parallel and axial misalignment, protecting sensitive components and reducing wear. These clamps are used in automation, machinery and motion control systems. They have aluminium construction for a high strength-to-weight ratio and structural rigidity. These clamps feature anodised aluminium finish for protection against corrosion and wear while providing a smooth and visually pleasing surface. They have a maximum operating speed of 4500 RPM to effectively handle dynamic loads and maintain the integrity of the coupled components. These clamps also exhibit remarkable heat resistance up to 225 degrees F.

Lovejoy ES-Series mini disc style couplings are used to run computers, robots, metering devices and medical equipment. These motion control couplings feature zero backlash design to correct parallel and angular misalignments up to .012 inches and 2 degrees, respectively. Further, they feature aluminium hubs with stainless steel discs to offer torsional stiffness up to 22125 in-lbs/rad and are capable of withstanding temperatures up to 300 degrees F. Choose from a wide range of these mini disc style couplings, available in variants delivering speed ranging from 2400 to 4800 rpm on Raptor Supplies.

Lovejoy Oldham couplings are used to connect two drive shafts for transmitting torque while accomodating parallel misalignment, absorbing shock and providing electrical isolation. These units feature two aluminium hubs with a polyacetal slotted disc allowing full-free movement of the hubs and providing torsional stiffness and high torque capacity at a maximum temperature of 176 degrees F. They further come with an anti-backlash design for eliminating the need of additional lubrication; ideal for use with shaft encoders, medical equipment and stepper motors. Choose from a wide range of these MOL Series couplings available in 3/16 to 1/2 inch bore diameters on Raptor Supplies.

Ruland Manufacturing MBC Series motion control couplings are installed on two shafts required to move at the same speed & in the same direction, while preventing misalignment between the shafts. They are ideal for small, dual-shaft applications to run medical equipment, robots, metering devices and computers. The one-piece design of the couplings easily fits the shafts, without causing marring. They are held in place via cap screws and have a spiral slot in the centre, to dampen vibrations. Choose from a wide range of motion control couplings, available in anodised aluminium and black anodised finish variants on Raptor Supplies.